Controllers & Monitors

AM-320 Saltwater Submersible Sensor Wand

$ 55.00

Product Description:

This accessory incorporates a mounting fixture at the end of a 40 inch (102 cm) segmented fiberglass wand and is well-suited for saltwater use. The wand unscrews into three sections for easier storage and transport. All radiation sensors are compatible with the wand, which allows the user to place the sensor in hard to reach areas such as in aquarium tanks and greenhouse.

View full product details »

Apogee MQ-510 Full Spectrum Underwater Quantum PAR Meter

$ 495.00

Product Description:

The MQ-510 quantum meter is designed for underwater PAR measurements and already applies the sensor's immersion effect correction factor to the meter readings through firmware. The meter provides excellent measurements under all light sources, including LEDs. The meter consists of a waterproof quantum sensor attached via waterproof cable to a handheld meter. The waterproof sensor incorporates a blue-enhanced silicon photodiode and custom optical filters with a rugged, anodized aluminum body with acrylic diffuser. The underwater quantum sensor is typically used in salt water aquariums where corals are grown. Note: The handheld meter is not waterproof, only the sensor and cable are waterproof.

Full-spectrum Sensor

Features an improved detector that provides excellent measurements under all light sources, including LEDs, right out of the box. The full-spectrum quantum sensor has a spectral range of 389 to 692 nm ± 5 nm seen in graph to the left. The sensor is available attached to a hand-held meter that provides a digital readout (MQ-510), with USB communication and custom software (SQ-520), and in multiple analog outputs to be used with a datalogger or voltmeter.

Ready for Underwater Use

All Apogee Underwater Quantum Meters and Sensors models (MQ-210, MQ-510, SQ-520) have the immersion effect correction factor preprogramed in the firmware or sensor software allowing the user to make excellent underwater measurements right out of the box. Sensors feature a waterproof sensor head that is potted solid for a complete seal and to ensure it has no hollow cavities for water to penetrate and cause measurement errors.

How is the MQ-510 different from previous Apogee quantum sensors?

The MQ-510 performs exactly the same underwater as the MQ-500, but the MQ-510 simply multiplies the PAR reading by 1.32 to account for the immersion effect. The MQ-510 is a full-spectrum quantum sensor (SQ/MQ-500 Series) with a spectral range of 389 to 692 nm ± 5 nm, which can be seen in the graph below. This improved spectral respose increases the acuracy of LED measurements.

Datalogging Capabilities

The MQ-210 and MQ-510 meters record up to 99 manual measurements. In logging mode the meter will make a measurement every 30 seconds. Every 30 minutes the meter will average the sixty 30 second measurements and record the averaged value. The meter can store up to 99 averages. The SQ-520 USB sensor has internal memory capable of storing 10,000 user-specified periodic measurements that can be downloaded to a computer.

Where is the MQ-510 used?

The MQ-510 is used to measure incoming PPFD measurements in aquarius environments.

specifications

Calibration Uncertainty ± 5 %
Measurement Range 0 to 4000 µmol m-2 s-1
Measurement Repeatability Less than 0.05 %
Long-term Drift (Non-stability) Less than 2 % per year
Non-linearity Less than 1 % (up to 4000 µmol m-2 s-1)
Response Time Less than 1 ms
Field of View 180 °
Spectral Range 389 to 692 nm ± 5 nm ( wavelengths where responsis greater than 50 %)
Spectral Selectivity Less than 10 % from 412 to 682 nm ± 5 nm
Directional (Cosine) Error Less than ± 5 % at 75° zenith anglean 10 % from 412 to 682 nm ± 5 nm
Azimuth Error Less than 0.5 %
Tilt Error Less than 0.5 %
Temperature Response -0.11 ± 0.04 % C-1
Uncertainty in Daily Totals Less than 5 %
Detector Blue-enhanced silicon photodiode
Housing Anodized aluminum body with acrylic diffuser
IP Rating IP68
Operating Environment 0 to 50 C; less than 90 % non-condesing relative humidity up to 30 C; less than 70 % non-condensing relative humidity from 30 to 50 C; separate sensors can be submerged in water up to depths of 30 m
Meter Dimensions 126 mm length; 70 mm width; 24 mm eight
Sensor Dimensions 24 mm diameter; 37 mm height
Mass 180 g
Cable 2 m of two conductor, shielded, twisted-pair wire; addititonal cable wire available; santoprene rubber jacket

View full product details »

Apogee SQ-420 Quantum PAR Meter (USB)

$ 269.99

Product Description:

The new SQ-420 smart quantum sensor can be connected directly to a computer for taking spot measurements or graphing and datalogging real-time PPFD using the included software. The sensor can also act as a stand-alone PAR datalogger by simply connecting it to any standard 5 V DC USB power plug. Internal memory within the sensor head is capable of storing 10,000 user-specified periodic measurements that can be downloaded as a CSV file to a computer for analysis.

The waterproof sensor incorporates a blue-enhanced silicon photodiode and custom optical filters with a rugged, anodized aluminum body with acrylic diffuser. Note: The handheld meter is not waterproof, only the sensor and cable are waterproof.

Original Sensor

A lower-cost option that is excellent for all light sources, except most LEDs, where post-measurement correction factors need to be applied to achieve accurate readings. The original quantum sensor has a spectral range of 410 to 655 nm seen in graph to the right. The sensor is available attached to a hand-held meter that provides a digital readout (MQ-210) and in multiple analog outputs to be used with a datalogger or voltmeter.

Spectral Response:

Datalogging Capabilities

The SQ-420 USB sensor has internal memory capable of storing 10,000 user-specified periodic measurements that can be downloaded to a computer.

Application

The SQ-420 is used to measure incoming and reflected PPFD around plants and other organisms in outdoor environments, greenhouses, growth chambers, and underwater.

Independent Calibration

The SQ-420 is calibrated independently for sunlight and electric light to improve measurement accuracy. The light source calibration can be selected in the settings menu of the Apogee software.

Software Overview:

specifications

Resolution

0.1 µmol m^-2 s^-1

Calibration Factor

Custom for each sensor and stored in the firmware

Calibration Uncertainty

± 5 % (see Calibration Traceability below)

Measurement Repeatability

Less than 1 %

Non-stability (Long-term Drift)

Less than 2 % per year

Non-linearity

Less than 1% (up to 4000 µmol m^-2 s^-1)

Response Time

Software updates every second

Field of View

180°

Spectral Range

410 nm to 655 nm (wavelegnths where response is greater than 50% of maximum; see Spectral Response below)

Directional (Cosine) Response

± 5 % at 75° zenith angle (see Cosine Response below)

Temperature Response

0.06 ± 0.06 % per C

Operating Environment

-40 to 70 C, 0 to 100% relative humidity; can be submerged in water up to depths of 30 m

Dimensions

24 mm diameter, 28 mm height

Mass

Sensor head weighs 90 g

USB Cable

4.6 m (15 ft)

Current Draw (when Logging)

5.1 mA

Warranty

4 years against defect in materials and workmanship

View full product details »

Apogee SQ-520 Full Spectrum Underwater Quantum PAR Sensor (USB)

$ 438.00

Product Description:

The new SQ-520 full-spectrum, smart quantum sensor can be connected directly to a computer via USB for taking spot measurements or graphing and datalogging real-time PPFD using the included software. The sensor can also act as a stand-alone PAR datalogger by simply connecting it to any standard 5 V DC USB power plug. Internal memory within the sensor head is capable of storing 10,000 user-specified periodic measurements that can be downloaded as a CSV file to a computer for analysis.

Full-spectrum Sensor

Features an improved detector that provides excellent measurements under all light sources, including LEDs, right out of the box. The full-spectrum quantum sensor has a spectral range of 389 to 692 nm ± 5 nm seen in graph to the left. The sensor is available attached to a hand-held meter that provides a digital readout (MQ-510), with USB communication and custom software (SQ-520), and in multiple analog outputs to be used with a datalogger or voltmeter.

Ready for Underwater Use

All Apogee Underwater Quantum Meters and Sensors models (MQ-210, MQ-510, SQ-520) have the immersion effect correction factor preprogramed in the firmware or sensor software allowing the user to make excellent underwater measurements right out of the box. Sensors feature a waterproof sensor head that is potted solid for a complete seal and to ensure it has no hollow cavities for water to penetrate and cause measurement errors.

How is the SQ-520 different from previous Apogee quantum sensors?

The SQ-520 performs exactly the same underwater as the MQ-500 series, but the SQ-520 simply multiplies the PAR reading by 1.32 to account for the immersion effect. The SQ-520 is a full-spectrum quantum sensor (SQ/MQ-500 Series) with a spectral range of 389 to 692 nm ± 5 nm, which can be seen in the graph below. This improved spectral response increases the accuracy of LED measurements.

Datalogging Capabilities

The SQ-520 USB sensor has internal memory capable of storing 10,000 user-specified periodic measurements that can be downloaded to a computer.

Where is the SQ-520 used?

The SQ-520 is used to measure incoming and reflected PPFD around plants and other organisms in outdoor environments, greenhouses, growth chambers, and underwater.

specifications

Calibration Uncertainty ± 5 %
Measurement Range 0 to 4000 µmol m-2 s-1
Measurement Repeatability Less than 0.05 %
Long-term Drift (Non-stability) Less than 2 % per year
Non-linearity Less than 1 % (up to 4000 µmol m-2 s-1)
Response Time Less than 1 ms
Field of View 180 °
Spectral Range 389 to 692 nm ± 5 nm ( wavelengths where responsis greater than 50 %)
Spectral Selectivity Less than 10 % from 412 to 682 nm ± 5 nm
Directional (Cosine) Error Less than ± 5 % at 75° zenith anglean 10 % from 412 to 682 nm ± 5 nm
Azimuth Error Less than 0.5 %
Tilt Error Less than 0.5 %
Temperature Response -0.11 ± 0.04 % C-1
Uncertainty in Daily Totals Less than 5 %
Detector Blue-enhanced silicon photodiode
Housing Anodized aluminum body with acrylic diffuser
IP Rating IP68
Operating Environment 0 to 50 C; less than 90 % non-condesing relative humidity up to 30 C; less than 70 % non-condensing relative humidity from 30 to 50 C; separate sensors can be submerged in water up to depths of 30 m
Meter Dimensions 126 mm length; 70 mm width; 24 mm eight
Sensor Dimensions 24 mm diameter; 37 mm height
Mass 180 g
Cable 2 m of two conductor, shielded, twisted-pair wire; addititonal cable wire available; santoprene rubber jacket

View full product details »

EcoTech VorTech Battery Backup

$ 173.25

In an aquarium with no flow, fish and corals begin to die in as little as 4 to 10 hours. The EcoTech VorTech Battery Backup is reef tank insurance in an aluminum housing.

By adding the VorTech Battery Backup, your tank is insulated from power interruptions, helping protect your valuable investment -and your tank inhabitants.

One EcoTech Marine Battery Backup will power one MP10wES or MP10ES for up to 72 hours, one MP40wES for up to 36 hours, one MP60wES for up to 20 hours.

*Hours are estimated and will vary depending on battery life, pump mode and other factors.

View full product details »

Innovative Marine AUQA Gadget Custom Cradle Universal Magnetic Probe Holder

$ 29.99

Introducing the all the new Custom Cradle.

A magnetically mounted, multifunction probe holder that organizes your devices in the most simple and efficient way possible.

Other probes racks can lead to an unorganized disaster. When it’s time to change, clean or calibrate, you’re left with everything in disarray! The Custom Cradle gives you a clutter-free solution to all these problems!

Eliminate thumb screws with the Custom Cradle’s magnetic catch system. The laser cut ATO and dosing holes, allow you to insert both with ease! Its low profile allows you to place it just about anywhere in your tank including the small spaces!

Preinstalled foam pads cradle your probes ensuring a tight fit. This combination gives you 3 points of contact and keeps your probes from accidently falling into your aquarium.

FEATURES:

Fully Encapsulated Magnet Mount
Magnetic Strength: 8mm (Nano) 12mm (XL) thickness
Magnetic Catch
No Thumb Screws
Padded Probe Holders: 3 (Nano) 4 – (XL)
Compatible with All Current Probes on the Market (including APEX Temperature Probe)
Dedicated Dosing Tube Holder: 2 (Nano) 4 (XL) – ¼” OD
Dedicated ATO Return Holder (XL Only) – ½” OD
Black Cell Cast Acrylic Construction
Dims: (Nano) 3.5” x 1.75” x 1.25” (XL) 6” x 1.75” x 1.25”

View full product details »

Innovative Marine AUQA Gadget DIY Mesh Screen Lid Kits

$ 29.99

We’ve got you covered.

Provide protection for your livestock and encase any aquarium with this complete Do-It-Yourself mesh screen lid kit.

Glass lids trap in heat, do not allow proper evaporation and build up salt creep that can hurt light penetration Stylish mesh screen tops are the answers to these woes by being lightweight, allow zero heat buildup and have very little impact on light penetration.

Each kit includes: a cut to size frame, trimmable mesh screen, spline and break-away corners for cord management

FEATURES:

Keeps livestock from leaving your tank
Powder coated for extra protection
Extra thick lightweight aluminum
Can be used for framed and rimless aquariums
Can be used with innovative Marine Lid Clips for rimless tanks (sold separately)
Available in three sizes: 24”x24”, 36”x24” and 48”x24”
Clip sizes available in 6, 8, 10, 12 & 15mm (sold separately)

View full product details »